Product ID:AA9277 EA 9394 PART A
MSDS Date:12/01/1991
FSC:8040
NIIN:01-288-5856
Kit Part:Y
MSDS Number: BYDLC

DEXTER ADHESIVES & STRUCTURAL MATERIALS

2850 WILLOW PASS RD
PITTSBURG, CA 94565-3299
US

Emergency Phone: 510-458-8000/202-483-7616

Info Phone: 510-458-8000/202-483-7616

Cage: 33564

DEXTER CORPORATION ADHESIVE & COATING SYSTEMS

312 BAY POINT, CA 94565-3299 US

Telephone: 202-483-7616

Cage: 33564

ALUMINUM (POWDER)

CAS: 7429-90-5

RTECS: BD0330000

Fraction By Weight: 30-60%

OSHA PEL 15 MG/CUM

ACGIH TLV: 10 MG/CUM (DUST)

EPICHLOROHYDRIN/BISPHENOL A TYPE EPOXY RESIN

Fraction By Weight: 10-30%

PROPRIETARY EPOXY RESIN

Fraction By Weight: 30-60%

SILICON DIOXIDE, CELITE 322

CAS: 7631-86-9

RTECS: VV3100000

Fraction By Weight: 1-5%

OSHA PEL 80 MG/CUM

ACGIH TLV: 0.1 MG/CUM

<108 L

RTECS: 9999999VO

LD50 LC50 Mixture:ORAL LD50 (RAT)IS 11,400 MG/KG INGRED #2
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:SKIN: IRRITATION/ALLERGIC
SENSITIZATION. EYES: IRRITATION.
Explanation of Carcinogenicity:THERE ARE NO INGREDIENTS ABOVE 0.1%
WHICH ARE IDENTIFIED AS CARCINOGENS BY NTP,IARC OR OSHA.
Effects of Overexposure:SKIN: RASH.
Medical Cond Aggravated by Exposure:PERSONS WITH PRE-EXISTING SKIN
AILMENTS MAY BE AT INCREASED RISK FROM EXPOSURE.

First Aid:EYES: FLUSH W/WATER FOR 15 MINS. SKIN: WASH W/SOAP & WATER.
INHALATION: REMOVE TO FRESH AIR. INGESTION: DRINK PLENTY OF WATER.
OBTAIN MEDICAL ATTENTION IN ALL CASES.

Extinguishing Media:DRY CHEMICAL, HALON FIRE EXTINGUISHER, WATER SPRAY,
FOAM OR FOG
Fire Fighting Procedures:USE A SELF-CONTAINED BREATHING APPARATUS AND
FULL PROTECTIVE EQUIPMENT.
Unusual Fire/Explosion Hazard:FIRE CONDITIONS MAY EVOLVE TOXIC FUMES.

Spill Release Procedures:WEAR PROTECTIVE CLOTHING. SCRAPE/SHOVEL INTO
DOT APPROVED WASTE CONTAINERS.

Handling and Storage Precautions:REFRIGERATED STORAGE IS RECOMMENDED TO
MAINTAIN PRODUCT QUALITY. PRODUCT MAY BE STORED AT 40F FOR UP TO 12
MONTHS.
Other Precautions:DON'T CUT, GRIND, WELD OR DRILL ON OR NEAR CONTAINER.
AVOID MIXING RESIN (PART A) & CURING AGENT (PART B) IN BATCHES >1
POUND UNLESS YOU PLAN TO USE IMMEDIATELY. DON'T HEAT MIXED ADHESIVE
>125F, UNLES S CURING SURFACES TO BE BONDED.

Ventilation:LOCAL EXHAUST AT POINT OF USE.
Protective Gloves:BUTYL RUBBER/POLYVINYL CHLORIDE/RUBBER
Eye Protection:SAFETY GLASSES W/SIDE SHIELDS
Other Protective Equipment:CHEMICAL GOGGLES, EYE WASH & SAFETY SHOWER,
NITRILE RUBBER GLOVES
Work Hygienic Practices:WASH AFTER HANDLING.
Supplemental Safety and Health
KEY1;T6.FOR PART B,REFER TO PNIND-D.SOURCE:PNIND-A,SAME NSN.

HCC:B2
Vapor Pres:0
Vapor Density:>1
Spec Gravity:1
Viscosity:4000-8000P
Solubility in Water:NEGLIGIBLE
Appearance and Odor:VISCOUS GRAY PASTE W/SLIGHT ODOR.

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS, STRONG LEWIS OR MINERAL ACIDS
Stability Condition to Avoid:AVOID MIXING BATCHES OF PT. A AND PT. B OF
MORE THAN 1 LB.DO NOT HEAT MIXTURE ABOVE 125F.
Hazardous Decomposition Products:CARBON DIOXIDE,CARBON MONOXIDE,OXIDES
OF NITROGEN,ALDEHYDES,ACIDS,UNDETERMINED ORGANICS.
Conditions to Avoid Polymerization:HEAT ABOVE 125F.

Waste Disposal Methods:INCINERATION IN AN EPA-APPROVED WASTE
INCINERATOR IS PREFERRED. DISPOSE OF IN ACCORDANCE W/FEDERAL, STATE
& LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.